They can look fantastic when they are first laid down. Give them a wet winter and you may see gaps and your sleeper leaning into the path.
Could be due to incorrect material. Could be a problem with the base/drainage.
Always know what your boundary is trying to hold before buying sleepers/edging.
Start With The Job, Not The Material
Your border is going to contain something i.e mulch and compost for a flower-bed or a higher ground level for a retaining wall.
The important thing here is retained ground. If your ground is being retained then your wall will receive force from the soil pushing against it. The higher your ground level, the more force it can become and if the majority of that force is placed on the upper half of your wall it can affect the required wall design.
Look at your site and establish how high your wall is, any load being placed nearby, ground conditions and available space.
These can include but are not limited to:
- Height of retained soil
- Load applied i.e drive, fence, path etc
- Ground conditions, is the soil solid, sloping, prone to water logging
- Available space to place your foundations, posts and drainage
Your average flower-bed could fall under simple landscaping tasks, a retaining wall with height, near buildings or slopes would require more knowledge and most likely the help of an adequate engineer.
So now that you know what you require, find an edging that can cope with your application’s demands.
What Timber Grading Actually Tells You
People always assume timber that looks good is suitable for your task, they are wrong. There are many aspects that play into your timber selection, its appearance, grade and durability.
As mentioned above you have your aesthetics, but there are further properties to look at. When selecting a timber for your design ask if they have been graded for strength and/or durability.
Depending on your application some species of tropical hardwood are good options to use. However be careful, depending on species and sapwood content, the timber can vary in how long it will last. If the timber is going to be used in exterior, ground contact, structural applications a softwood will need to be treated to at least a UC4. Again, don’t go on the assumption that your timber is protected based on colour, check the treatment it’s had.
Always select a timber that is correct for your application, just because it’s heavy doesn’t mean it’s good for the job at hand.
Build A Base That Won’t Move
Sleepers are very dense, therefore people believe that once they are on the ground they will hold themselves up. They won’t.
As the ground around and below your wall can settle, joints can form and courses of sleepers can begin to lean forward due to soil pressures.
Make sure your border is on level, firm ground and follow the instructions given to fix your timber edging. Make sure the sleepers are offset from each other and pin your corners. Do not simply place your timber sleepers onto the ground and expect them to remain true.
If your border is acting as a retaining wall, you will need posts and foundations that can withstand your applications. How deep and spaced these are out can depend on many variables, please don’t base yours off a picture you found online.
Always check your walls periodically, if you notice gaps forming, bowing sleepers or posts beginning to move it could indicate an issue with the ground below. Adding more screws isn’t going to cure the problem you already have.
Drainage Comes Before Decoration
Water plays a big role in the lifespan of your timber, the two ways it can hurt your wood is by keeping it constantly saturated and causing pressure build up in your retained soil.
According to the Wood Protection Association once your timber hits a moisture content above 20% your chances of biological attack is greatly increased. Of course, there is no guarantee that your sleeper will fail, but it’s something to consider when building a retaining wall.
There are multiple ways you can help reduce this issue, free draining soil behind the wall, a mesh or aggregate barrier to prevent fines entering your drain, and a drain with an outlet that discharges water away from your structure/neighbour’s property.
Having an outlet for your drain is extremely important, if the pipe runs along the back of your wall and has no exit point it won’t do you any favours. Remember to also consider where the collected water will run, if it lands near your house or someone else’s it can cause flooding.
Flower-beds may not need much drainage, but again, ensure they’re able to drain, maybe they’re located on a hard standing surface?
There’s no substitute for good design, drainage will just help ensure your structure stays true.
When Sleepers Aren’t The Best Choice
Not every boundary will need timber sleepers, you may require a smaller, less bulky material that fits your garden better.
Edging timber can be used for flower-beds, walkways and small paths. Again, find a material that suits your applications and don’t leave vulnerable timber exposed in ground that tends to saturate.
Stone or concrete will also produce a nice boundary line, just be aware like timber, they can also fail if the ground below begins to sink. Use correct fixings and foundations when laying your boundary.
Steel edging can be useful for rounded lawn areas, find a profile that can handle your soils and use stake rods to keep them in place. These are not intended to retain large volumes of soil.
Unlike timber, recycled plastic edging won’t experience rot but may require extra fixings if long spans are needed.
If you want to use railway sleepers, always be careful about where they come from. The RHS recommend that you never reuse old railway sleepers that have been treated with creosote, due to contact hazards.
Always consider other methods of creating a retaining wall, perhaps you require a higher grade solution than sleepers can offer?
What To Ask Before You Order
Don’t only focus on cost per linear metre, this won’t cover your costs.
Below are some useful questions that you should know answers to before you make a purchase.
- What am I buying?
Ensure the timber that’s being supplied is what’s called out on your drawings, double check thickness, species and timber grading if structural.
- Will my timber be suitable?
Based on the above information, find a timber that will withstand the exposure it’s going to be subjected to, get supporting documentation if applicable.
- What do I need to fix?
Depending on your fixings, they may not be compatible with your chosen timber, treat or species, investigate further before you buy.
- Can I deliver the timber?
Make sure you can gain access to your site, timber sleepers are bulky and can take time to install, factor this into your lead time.
- Where is my timber coming from?
If you’re buying tropical timber, ensure you know your species, origin and have valid certificates if required.
Once you understand your requirements, you can select a material that will fit your project correctly, instead of relying on cost and replacing your timber as the ground shifts below you.
Wrapping It Up
Know what you’re looking to do, is it a border or retaining wall? Find out what your timber is being sold on, is it aesthetically pleasing, has been graded for strength and durable enough to survive its surroundings.
Once you’re satisfied, look into base work and make sure your timber can shed water, if all of these are accounted for your boundary should stand tall for many winters to come.